Jam Making Basics

How to Sterilize Jars for Jam and Jelly Safely

Wash, heat, and fill jars the safe way for jam and jelly. Learn when sterilizing is required, how to boil jars at altitude, and how to use new lids.

On this page
  1. The short answer
  2. Do you need to sterilize jars?
  3. Step 1: Inspect and wash
  4. Step 2: Boil empty jars
  5. Step 3: Keep jars and jam hot
  6. Lids and bands
  7. Other methods you will see
  8. Step 4: Fill and seal
  9. Freezer jars
  10. Rubber-ring jars
  11. Where to go next

The short answer

Wash jars and lids in hot, soapy water, check each jar for chips, and keep the jars hot until you fill them. If a jam will be processed for less than 10 minutes, the tested method is to boil the empty jars for 10 minutes first. Use new lids every time.

Do you need to sterilize jars?

It depends on how long the filled jar is processed.

  • Processed for less than 10 minutes. The National Center for Home Food Preservation says jams, jellies, and pickled products processed for less than 10 minutes should be filled into sterile empty jars. Sterilize them with the boiling water method below.
  • Processed for 10 minutes or longer. Pomona’s Pectin reports that USDA guidance does not require presterilizing empty jars for jam or jelly processed this long. Clean, hot jars are still needed.
  • Freezer jam. There is no processing step. Use clean, freezer-safe jars or containers.

Step 1: Inspect and wash

  • Check every jar for chips, cracks, and sharp rims, and discard any damaged glass.
  • Wash the jars and bands in hot, soapy water, then rinse well.
  • Use new flat lids for every batch. The sealing compound on a lid is designed to seal once.

Step 2: Boil empty jars

The National Center for Home Food Preservation describes this method for empty jars:

  1. Place the clean jars right side up on the rack in a boiling water canner.
  2. Fill the canner and jars with hot water, not boiling, to about 1 inch above the tops of the jars.
  3. Boil for 10 minutes at elevations below 1,000 feet.
  4. At higher elevations, boil 1 additional minute for each additional 1,000 feet.
  5. Remove the jars one at a time and drain them. Save the hot water to process the filled jars.

Step 3: Keep jars and jam hot

Keep the jars hot, either in the canner or on a clean towel, until you fill them. Cold jars can crack when hot jam goes in. The jam should be hot too. If it cools while you work, reheat it before filling.

Lids and bands

  • Keep the new lids in a small pan of hot water, not at a rolling boil. Boiling can damage the sealing compound. Follow the instructions that came with your lids.
  • Screw the bands on fingertip tight. Do not crank them down.

Other methods you will see

  • Oven. Many people dry jars in a low oven, around 275°F (140°C), for about 10 minutes. It is a popular method, but the national canning guides describe the boiling water method. For jars you will process for shelf storage, use the boiling water method.
  • Dishwasher. A hot cycle can clean jars well, but the jars still need to be hot when you fill them.

Step 4: Fill and seal

  • Leave 1/4 inch of headspace for jam and jelly.
  • Wipe the rims with a clean, damp cloth before you add the lids.
  • Add the lids and screw the bands on fingertip tight.
  • Process the jars as your recipe says. How long to water bath can jam explains the timing.

Freezer jars

For freezer jam, leave 1/2 inch of headspace in freezer-safe containers, and freeze the jam once it has cooled. Thaw it before eating. Pomona’s Pectin advises eating frozen jam within about a year.

Rubber-ring jars

If your jars have rubber rings, remove the rings before washing. Boil the rings in a small pan of water for 2 to 3 minutes. Dry oven heat damages rubber, so do not dry the rings in the oven.

Where to go next

The complete guide to jam making basics

Making Jams and Jellies at Home: A Beginner's Guide
Read the guide

Keep exploring

Guides from other topics

All topics →