Jam Making Basics

How to Tell When Jam Is Done Cooking: The Cold Plate Test and Other Methods

Use a thermometer, the cold plate test, or the spoon test to tell when jam is done. Learn the set point and why jam keeps thickening as it cools.

On this page
  1. The short answer
  2. Why jam has a set point
  3. Test 1: Thermometer
  4. Test 2: Cold plate (the wrinkle test)
  5. Test 3: Spoon (sheet) test
  6. What set jam looks like
  7. Jam keeps setting as it cools
  8. Common mistakes
  9. Where to go next

The short answer

Jam is done when it reaches its set point, about 220°F (104°C) at sea level, or when it passes a gel test, such as a wrinkle on a cold plate or a sheet off a spoon. Take the pot off the heat while you test. Jam keeps thickening as it cools, so a batch can look loose and still set.

Why jam has a set point

Pectin, sugar, and acid form a gel once the mixture has cooked long enough to lose enough water. The set point is the temperature at which that happens. At sea level, most jams set at about 220°F (104°C). The number changes with altitude, which is covered below.

Test 1: Thermometer

A candy or jelly thermometer is the most consistent way to check. Clip it to the side of the pot so the tip is in the jam and not touching the bottom.

  • Check the thermometer first. Put it in boiling water. At sea level it should read 212°F (100°C). If it reads differently, note the difference and adjust your target by the same amount.
  • Aim for about 8°F above the boiling point of water where you live. At sea level that is 220°F.
  • Read it at a full rolling boil, stirring so the reading reflects the whole pot.

Altitude matters. Water boils at a lower temperature the higher you go, so the target drops too. As a rough guide, subtract about 2°F for every 1,000 feet of elevation. Check the figure for your town if you live high up.

Test 2: Cold plate (the wrinkle test)

  1. Before you start cooking, put two or three small plates in the freezer.
  2. Take the pot off the heat, and spoon a small amount of jam onto a cold plate.
  3. Wait 30 seconds to a couple of minutes. Push the edge of the jam with your finger.
  4. If the surface wrinkles and holds a path when you push it, the jam is set. If the jam flows back together, keep cooking.
  5. If it is not set, return the pot to the heat, and test again every few minutes.

Test 3: Spoon (sheet) test

Dip a cool metal spoon into the boiling jam, then lift it and turn it sideways. Watch the drips. Jam that is close to set falls in heavy drops that run together and come off the edge in a sheet. Jam that runs off in thin streams is not ready.

What set jam looks like

Set jam looks glossy and slightly thick. The bubbles are heavier and slower, with less foam on top. The jam clings a little to a spoon or spatula when you stir it.

Jam keeps setting as it cools

Jam firms up as it cools, and some batches take up to a week to reach their final set. A jam that is loose right after jarring may still set in the jar. Do not keep boiling a batch to force a set, because overcooking darkens the fruit and dulls the flavor. Fixing jam that won’t set covers what to do if it stays runny.

Common mistakes

  • Testing with an uncalibrated thermometer. Check it in boiling water before each batch.
  • Testing on the heat. Take the pot off the heat while you test, or the jam keeps cooking.
  • Cooking too long. Overcooked jam is darker, tastes cooked, and can turn tough.
  • Using a narrow pot for a big batch. A large batch in a narrow pot takes longer to reach the set point, and the fruit overcooks while you wait.
  • Judging by time alone. Recipe times are estimates. Test for the set.

Where to go next

The complete guide to jam making basics

Making Jams and Jellies at Home: A Beginner's Guide
Read the guide

Keep exploring

Guides from other topics

All topics →